Pinterest

May 30, 2013

yellow rope bracelets 2863


 This collection of knotted bracelets is made from a very soft and flexible synthetic cord. As you can see the color is a bright yellow with red and blue thread accents. The red and blue are actually individual strands of the woven sheath which surrounds the core.

This material came from a big-box retailer and is a 9/16" diameter made with a soft fiber core so it is very soft to the touch and quite flexible.


 On the left is the single strand design minimal profile only 1/2" (13 mm) wide.

In the center is the two strand design a bit more substantial at 1 1/8" (28 mm) but very soft and stretchy.

On the right is the symmetrical three part three strand design a full 1 3/4" (33 mm) wide.

Available from extra small to extra large. This group measures between 6 1/2" (165 mm) to 7" (178 mm)

You can choose size and width when you order

                      available here


design and photographs © copyright 2013 WhatKnotShop

May 24, 2013

nylon hybrid weave turks head knot bracelet 2760

 Two weave patterns are combined in this interesting knot bracelet: Each edge has a herringbone (over 2-under 2) pattern which then shifts to a plain weave in the center.

This design is a "square" turks head with 14 bights and 15 parts.

Here is a related wider design.



The material is a 1/8" high density braided nylon cord which is a nice bright white color. This material is easy to work in the knot and unlike cotton tends to hold it's size without shrinking.

size relaxed:
7" (178 mm) inside circumference
2 1/4" (55 mm) inside diameter
2 3/4" (96 mm) wide

will stretch slightly to about 7 1/2"
The weave pattern is:
U2-O2-u1-o1-u1-o1-u1-o1-U2-O2 which has been doubled to bulk up the size.


                     Available here

design and photographs © copyright 2013 WhatKnotShop

May 23, 2013

two part rope bracelet 2797

 This two part weave design is made using a mold and a segment of braided cotton line. The cord is laid out loose on the mold then the second pass is looped under the first pass 13 times. This pattern is tripled and the loose ends laid parallel.

The shape is worked up to a firm fit on the mold.
 This type of knot is inherently unstable so there is an invisible web of nylon thread that holds the pattern secure. This thread is edge stitched through the plies and across the knot at the crossing points.

Here's a similar design made with glass beads at the crossing points.

This example is about 8" (205 mm) inside circumference.
Many size variations are possible with this design. It can be made on a larger mold with more crossings or smaller with fewer crossings. The diameter of the cord can be changed to adjust proportions and scale.



design and photographs © copyright 2013 WhatKnotShop

May 18, 2013

wrapped leather cord button bracelet 2781

 This design is made from 2 mm round leather cord waxed cotton thread a wood bead and a plastic button.

It's a lightweight sophisticated accessory that will add a touch of boho style.
This detail shows the loops and the button closure. The bead adds a little symmetry to the closure system.
The waxed thread is wrapped around the cords securing them tightly. A loop is used to capture the loose end which is then pulled under the wrap then the ends are trimmed.

Soon to be available online.




design and photographs © copyright 2013 WhatKnotShop

May 8, 2013

ultra slender string grommet bracelets 2801

 Grommets are pieces of rope or line that have been unlaid then twisted back into a circular form.

Here's a tutorial that shows how traditional grommets  are made.

Here's a video showing the same process.

The design shown on the left  is made with a waxed thread whipping to bind the loose ends instead of the splicing shown in the tutorial.
 The material used is a white #60 cotton cord which is about 1/8" (3 mm) diameter.

I measure about 3 1/2 circumferences of cord then cut the piece and un-lay it. This creates three strands, each has a "corkscrew" shape due to the original construction of the cord.

As in in the tutorial above the cord is re-twisted in the circular form three times around. The ends are laid parallel and the whipping is applied.
Here you can see the white whipping cord that binds the loose ends which have been trimmed off in the photo.

A variety of sizes is available, this one is a 6" circumference. These are very sturdy and can be stretched hard to slip them over your hand. They will shrink back to original size or slightly smaller if you get them wet.

                   Available here
design and photographs © copyright 2013 WhatKnotShop

May 6, 2013

Lima bean beaded one button cuff bracelet 2792

 Here's another variation on polymer clay beads used in the one button bracelet designs. This one features smooth ribbed beads that resemble lima beans in shape. The holes are made in the base of the bead to enable edge stitching to secure the bead in place.

Here's another design made with these custom made beads you might like.

Read the tutorial explaining how to make the one button toggle bracelet here.
 The button toggle is made out of the same material as the beads: light tan polymer clay baked for 15 minutes in the oven.

You can see the back side of the lima bean beads in the center of the cord fabric.

The framing cords are a dark pearl grey. The infill cords are an olive taupe cotton both hand dyed in my basement laundry room.

This playful design is about 7" (178 mm) inside diameter.

                 Available here

See more of these unique creations in the fiber art section of my Etsy shop.



design and photographs © copyright 2013 WhatKnotShop

May 3, 2013

dinosaur spiked bracelet 2793

This sculpy project involves creating beads that resemble the protruding plates of a stegosaurus and incorporating them into a one button design. This spiky bracelet is a companion piece to the Stegosaurus spiked rope bracelet.

The color is a light tan with grey orange and yellow cords. The framing cords are off-white. The button is also made with the tan clay.

Size is a "small" 7" (178 mm) inside circumference.


 The beads are made with two holes to enable a firm connection to the fabric. You can see these holes in the photo on the left.

The bracelet is constructed the same way as shown in this tutorial with the added beads.

Here's another design made with less aggressively shaped beads you might like.


or maybe this one would be interesting as well
See more of these playful designs in the fiber art section of my Etsy shop.






design and photographs © copyright 2013 WhatKnotShop